© jkj,gwww.itda.ac.id 2024

Detail Skripsi

PENGARUH VARIASI UKURAN SERBUK BATANG JAGUNG BERMATRIK LIMBAH PLASTIK PET TERHADAP SIFAT FISIS PAPAN KOMPOSIT
Penulis
NOVAN DIMAS WIJAYA
Pembimbing : Fajar Nugroho, S.T.,M.Eng - Ir. Sudarmanto, M.T

ABSTRAK :
PENGARUH VARIASI UKURAN SERBUK BATANG JAGUNG BERMATRIK LIMBAH PLASTIK PET TERHADAP SIFAT FISIS PAPAN KOMPOSIT Disusun oleh: NOVAN DIMAS WIJAYA 16040001 Pembimbing 1: Fajar Nugroho, S.T.,M.Eng. Pembimbing 2: Ir.Sudarmanto,M.T. ABSTRAK Polyethilene Therepthalate (PET) merupakan jenis plastik yang keberadaannya melimpah sehingga menjadi salah satu limbah rumah tangga. Salah satu cara untuk menanggulangi sampah plastik adalah dimanfaatkan sebagai bahan papan komposit. Batang jagung merupakan bahan lignoselulosa tinggi sehingga dapat dimanfaatkan sebagai filler (bahan pengisi) dalam papan komposit. Penelitian ini bertujuan untuk mengetahui pengaruh variasi ukuran serbuk batang jagung terhadap sifat fisis (kerapatan, kadar air, pengembangan tebal) pada papan komposit. Penelitian ini menggunakan variasi serbuk batang jagung dengan ukuran 60, 80, dan 100 mesh. Komposisi papan komposit serbuk batang jagung dengan limbah plastik PET menggunakan perbandingan 60% : 40% dari volume total papan komposit. Hasil penelitian menunjukkan bahwa semakin kecil ukuran serbuk, nilai kerapatan papan komposit semakin tinggi. Sedangkan pada pengujian kadar air dan pengembangan tebal, semakin kecil ukuran partikel batang jagung semakin rendah nilai pada pengujian tersebut. Nilai kerapatan tertinggi sebesar 0,90 g/cm3,nilai kadar air terendah sebesar 0,31%, dan nilai pengembangan tebal terendah sebesar 2,11% terjadi pada ukuran 100 mesh. Hasil penelitian ini sesuai SNI 03-2105-2006. Dari hasil tersebut menunjukkan hasil pengujian terbaik yang terdapat pada variasi ukuran serbuk batang jagung 100 mesh. Dengan demikian, batang jagung dan limbah plastik PET dapat dimanfaatkan sebagai papan komposit alternatif pengganti kayu sebagai interior rumah tangga. Kata kunci: PET, batang jagung, sifat fisis, ukuran mesh, papan komposit ii THE EFFECTS OF POWDER SIZE VARIATIONS OF CORN STALK POWDER WITH PLASTIC WASTE PET ON THE PHYSICAL PROPERTIES OF COMPOSITE BOARD Written by: NOVAN DIMAS WIJAYA 16040001 Supervisor 1: Fajar Nugroho, S.T., M.Eng. Supervisor 2: Ir.Sudarmanto, M.T. ABSTRACT Polyethilene Therepthalate (PET) is a type of plastic with abundant existence that becomes the household wastes. One way to overcome plastic waste is to use it as a composite board material. Corn stalk is a high lignocellulosic material which can be used as a filler in composite boards. This study aimed to investigate the effects of size variations of corn stalk powder on the physical properties (density, moisture content, thickness expansion) of the composite board. This study usedvariations of corn stalk powder with sizes of 60, 80, and 100 mesh. The composition of corn stalk powder composite board and PET plastic waste was 60%: 40% of the composite boardtotal volume. The results showed that the smaller size of the corn stalk powder, the higher the density value of the composite board occurred. Meanwhile, in the experiment of water content and thickness expansion, the smallerthe size of corn stalk powder the lower the value of the experiment occurred. The highest density value as 0,90 g/cm3, the lowest water content value as 0,31%, and the lowest thickness development value as 2,11% occurred at 100 mesh size. The results of the research were in accordance with SNI 03-2105-2006. The best test results were found in variations in the size of corn stalk powder 100 mesh. Thus, corn stalks and PET plastic waste can be utilized as alternative composite boards for wood substitutes as household interiors. Keywords: PET, corn stalk, physical properties, mesh size, composite board Approved by, Dewanti Ratna


Tulisan Lengkap dapat Dibaca di Ruang Tesis/Disertasi
Penulis : NOVAN DIMAS WIJAYA
NIM : 16040001
Foto :
File : [ Baca file skripsi ]
   

E-LibSTTA

Sistem Informasi Perpustakaan STTA Yogyakarta

© E-LibSTTA 2024